APCRBC154-UPC UPC Compatible Replacement Battery for APCRBC154, UPS Battery Backup 600VA: BE600M1, BN650M1, BN675M1, BE670M1 by Upgrade Parts Company

For more than 20 years, UPC UPGRADE PARTS COMPANY has become a trusted manufacturer of high quality UPS replacement battery cartridges. All products are “Assembled in the USA” allows us to provide real value to our customers. UPC UPGRADE PARTS COMPANY enhances its’ product offerings through a dedicated new product development process so we have the replacement battery cartridge you need at the time you need it. Our products are readily available in the US. Possible Installation Issues ( # - Issue , A – Cause , B – Resolution) 1. The BackUPS is turned on, the POWER button alternates between green-red and the unit emits a constant tone a. The BackUPS is not connected to AC power, there is no AC power available at the wall outlet, or the AC power is experiencing a brownout or over voltage condition. b. Make sure the power cord is securely connected to the wall outlet, and that there is AC power available from the wall outlet. Where applicable, check that the wall outlet is switched on and a circuit breaker did not trip. 2. Connected equipment loses power a. A BackUPS overload condition has occurred. b. Remove all nonessential equipment connected to the UPS outlets. One at a time, reconnect equipment to the BackUPS. Charge the battery for 24 hours to make sure it is fully charged. If the overload condition still occurs, replace the battery. a. The BackUPS battery is completely discharged. b. Connect the BackUPS to AC power and allow the battery to recharge for ten hours 3. The POWER button is green and flashes twice every 2 seconds a. The BackUPS is operating on battery power. b. The BackUPS is operating normally on battery power. At this point the user should save all open files, and shutdown the computer. When AC power is restored, the battery will recharge. 4. The POWER button flashes green in rapid succession. a. The BackUPS battery has approximately two minutes of remaining runtime. b. The BackUPS battery is near a total discharge state. At this point the user should save all open files, and shutdown the computer. When utility power is restored, the battery will recharge. 5. The alarm is on with a constant tone and the UPS is off a. The UPS was on battery and the connected load exceeded the rated load of the UPS. b. Turn off the UPS. Disconnect all devices. Turn on the UPS and reconnect the devices one at a time. 6. The USB port charging stops, and the Power On LED alternately illuminates green-amber a. The USB port has detected a short circuit or has detected a fault. b. Disconnect cable and device from the USB port. USB charging will resume when the POWER button turns green. 7. The UPS and outlets are off, but the UPS keeps beeping twice every 30 seconds (Quiet Alarm mode) or keeps beeping once every 4 seconds (Full Alarm mode) a. In this situation the voltage is not low enough to shutdown the UPS but not high enough to start the UPS and power the outlets. There is however enough voltage to charge the UPS. b. Use Quick Mute to mute the alarm. The UPS will return to normal operation once the AC input voltage has returned to a

• Direct Replacement: Fully compatible replacement for APCRBC154, designed for APC Back-UPS models BE600M1, BN650M1, BN675M1, and BE670M1. Ideal for restoring reliable APC battery backup performance.
• Precise Fit and Dimensions: Measures 5.95" L x 2.01" W x 3.90" H with T2 terminals for a secure, easy installation in your existing Back-UPS system.
• Maintenance-Free Performance: Sealed lead-acid battery with a suspended electrolyte design—pre-charged and ready to use right out of the box for dependable backup power.
• Warranty and Support: Backed by an 18-month warranty on all UPC-branded batteries for lasting performance and peace of mind.
• Reliable Power Protection: Keep your connected devices safe during power outages or surges with a high-quality battery backup replacement that meets or exceeds OEM specifications.